Raypak heater "Rollout SW Open" (2024)

tlwilson

0

LifeTime Supporter

Aug 15, 2010
50
Nebraska
  • May 18, 2013
  • Add bookmark
  • #1

We bought a new heater this season, a Raypak 206,000 BTU NG Electric Heater RHM-15-9962. It heated the pool nicely earlier in the week, but we turned it off when a cool spell was forecast. This morning I tried to turn it on and I get this error message: "Rollout SW Open". What does this mean? I appreciate the help.

JasonLion

0

TFP Expert

Platinum Supporter

LifeTime Supporter

May 7, 2007
37,770
Silver Spring, MD
  • May 18, 2013
  • Add bookmark
  • #2

Here is what I found in the manual: Roll Out Sw Open - Rollout Switch - verify gas pressure, combustion air, blocked heat exchanger, proper vent size/connections, high wind conditions.

ps0303

0

TFP Expert

In The Industry

Jul 6, 2011
4,177
FL
  • May 19, 2013
  • Add bookmark
  • #3

The rollout switch is activated when something like wind causes the flames to shoot out towards the front of the unit. This is usually caused by high winds while the unit is running. Are you sure it it said rollout? Sounds odd that you turn it on and the switch is open.

The rollout switch connects inside the cabinet right behind where the gas pipe comes into the gas valve. I have seen a few cases where the installer moved the rollout switch so they could install the gas pipe and they failed to put it back in place. This dangling switch is right by the burners then and when the units lights, its possible for the switch to trip open.

In any case this unit is under warranty. Hopefully your installer is also a warranty person for Raypak. Call them and have them come back and look at why the switch failed.

tlwilson

0

LifeTime Supporter

Aug 15, 2010
50
Nebraska
  • May 19, 2013
  • Add bookmark
  • #4

Thank you for your reply. It definitely says "Rollout SW Open". I will call the installer for the repair.

tlwilson

0

LifeTime Supporter

Aug 15, 2010
50
Nebraska
  • Jun 14, 2013
  • Add bookmark
  • #5

Our heater is still not fixed. They determined it wasn't getting enough gas so the gas company replaced our meter. Turned it on and the same thing happened. Now they say the wind diminished the flame and did something to the fireman's switch. Fireman's switch replaced and the wind keeps blowing out or diminishing the flame. Back and forth on how to protect it from the wind. Anybody with advice?

ps0303

0

TFP Expert

In The Industry

Jul 6, 2011
4,177
FL
  • Jun 15, 2013
  • Add bookmark
  • #6

The only thing you can do is add a wind stack to it. You've never had this issue before wind?

tlwilson

0

LifeTime Supporter

Aug 15, 2010
50
Nebraska
  • Jun 15, 2013
  • Add bookmark
  • #7

Our previous heater never had this problem. It was old and inefficient (still worked), but we wanted to upgrade. Raypak heater "Rollout SW Open" (8)

ps0303

0

TFP Expert

In The Industry

Jul 6, 2011
4,177
FL
  • Jun 15, 2013
  • Add bookmark
  • #8

Add the Raypak high wind stack. Probably $100 or around there.

tlwilson

0

LifeTime Supporter

Aug 15, 2010
50
Nebraska
  • Jun 15, 2013
  • Add bookmark
  • #9

Thanks for the help. I appreciate it!

B

[emailprotected]

0
Aug 26, 2014
1
Pensacola Florida
  • Aug 26, 2014
  • Add bookmark
  • #10

How did you solve the problem

Enjoying this content?

Support TFP with a donation.

Give Support

Jun 6, 2013
898
IL
  • Aug 26, 2014
  • Add bookmark
  • #11

I wonder if you have a bad roll out switch. My old RP2100 heater had a wax one and I replaced it with a solid state one. It had a red reset button on it. That solved my roll out problem at the time. They also sell roll out switches that have different shutoff temps by about 10-15deg if I remember but you may not want to go there. I did buy one of the solid state versions which was higher but didn't need it.

J

Jayryght

0
Aug 19, 2016
11
Toronto, Canada
  • Aug 19, 2016
  • Add bookmark
  • #12

I have the same problem. Just happened to me today. I bought and got my heater installed in October 2013 and it heated the pool really nicely. I haven't used the heater in about a week. It's been really hot in Toronto. Today I wanted to do an evening swim with the kids and my wife so I thought I'd turn it on and had the "Rollout SW Opem" message. I thought it was a glitch so I cut the power to the unit and turned it back on, cut the gas and turned it back on, opened up the panel and cleaned any debris I could with a cloth rag and nothing. After reading the comments here I have located the switch but it does not have a reset button. I read somewhere that the newer models do not have one. Is it time to call for service or is there anything else I can do on my end? RSVP

Pool Clown

In The Industry

Sep 5, 2008
2,186
Silicon Valley, CA
  • Aug 20, 2016
  • Add bookmark
  • #13

If it is a Raypak heater, the roll out sensor is a one time use part, like a fuse, it isnt re-settable. I would replace it, leave the front cover removed, start the heater, and observe if the flame "rolls out". If you see this happen, turn off the heater immediately, and have a tech check the exchanger for sooting.

J

Jayryght

0
Aug 19, 2016
11
Toronto, Canada
  • Aug 20, 2016
  • Add bookmark
  • #14

Pool Clown said:

If it is a Raypak heater, the roll out sensor is a one time use part, like a fuse, it isnt re-settable. I would replace it, leave the front cover removed, start the heater, and observe if the flame "rolls out". If you see this happen, turn off the heater immediately, and have a tech check the exchanger for sooting.

I tried that. It doesn't even ignite. Nothing happens. It is just the error message.

wjr75

0

LifeTime Supporter

Jun 6, 2013
898
IL
  • Aug 20, 2016
  • Add bookmark
  • #15

You can jumper across the roll out sensor to see if it starts. This is just for testing purposes and shouldn't be left that way. Might have blown the replaced sensor again or may have some other board issue.

Pool Clown

In The Industry

Sep 5, 2008
2,186
Silicon Valley, CA
  • Aug 20, 2016
  • Add bookmark
  • #16

Jayryght said:

I tried that. It doesn't even ignite. Nothing happens. It is just the error message.

Did you replace the roll out sensor?
Trace the roll out sensors' wires all the way back to the board to make sure they haven't been chewed on.

J

Jayryght

0
Aug 19, 2016
11
Toronto, Canada
  • Aug 20, 2016
  • Add bookmark
  • #17

Re: Raypak heater "Rollout SW Open"

@wjr75 How do I do that? "Jumper across the rollout sensor?"

- - - Updated - - -

@pool clown: no I did not replace it. Not sure how to do that? I see the wires tracing up towards panel, but I guess I have to take off the panel to see it's source right?

- - - Updated - - -

@pool clown: no I did not replace it. Not sure how to do that? I see the wires tracing up towards panel, but I guess I have to take off the panel to see it's source right?

wjr75

0

LifeTime Supporter

Jun 6, 2013
898
IL
  • Aug 20, 2016
  • Add bookmark
  • #18

To jumper across you need a wire across the two terminals where the fuse (roll out sensor) is plugged into. If you do any electrical testing you usually have an alligator clip jumper wire which has one on both ends. But as said before this would be temporary.

J

Jayryght

0
Aug 19, 2016
11
Toronto, Canada
  • Aug 21, 2016
  • Add bookmark
  • #19

@wjr75 Thanks for the tip but I know verrrry little about electrical work and I don't even know what an alligator clip jumper wire is. At this point I may bite the bullet and call a tech. Kudos for your help though.

ps0303

0

TFP Expert

In The Industry

Jul 6, 2011
4,177
FL
  • Aug 22, 2016
  • Add bookmark
  • #20

Yes if you don't know much about electric or gas, call a tech and have them check it out.

Enjoying this content?

Support TFP with a donation.

Give Support

You must log in or register to reply here.

Raypak heater "Rollout SW Open" (2024)
Top Articles
Latest Posts
Recommended Articles
Article information

Author: Pres. Carey Rath

Last Updated:

Views: 5847

Rating: 4 / 5 (61 voted)

Reviews: 84% of readers found this page helpful

Author information

Name: Pres. Carey Rath

Birthday: 1997-03-06

Address: 14955 Ledner Trail, East Rodrickfort, NE 85127-8369

Phone: +18682428114917

Job: National Technology Representative

Hobby: Sand art, Drama, Web surfing, Cycling, Brazilian jiu-jitsu, Leather crafting, Creative writing

Introduction: My name is Pres. Carey Rath, I am a faithful, funny, vast, joyous, lively, brave, glamorous person who loves writing and wants to share my knowledge and understanding with you.