Raft foundation (2024)

Foundations provide support for structures, transferring their load to layers of soil or rock that have sufficient bearing capacity and suitable settlement characteristics.

Very broadly, foundations can be categorised as shallow foundations or deep foundations. Shallow foundations are typically used where the loads imposed by a structure are low relative to the bearing capacity of the surface soils.

Deep foundations are necessary where the bearing capacity of the surface soils is not adequate to support the loads imposed by a structure and so those loads need to be transferred to deeper layers with higher bearing capacity.

Shallow foundations include:

• Strip foundations (or footings).
• Pad foundations.
• Raft foundation.

Raft foundations (sometimes referred to as raft footings or mat foundations) are formed by reinforced concrete slabs of a uniform thickness (typically 150 mm to 300 mm) that cover a wide area, often the entire footprint of a building. They spread the load imposed by a number of columns or walls over the area of foundation, and can be considered to ‘float’ on the ground as a raft floats on water.

They are suitable where:

• Floor areas are small and structural loadings are low, such as in one or two-storey domestic buildings.
• A basem*nt is required.
• Ground conditions are poor and strip or pad foundations would require significant excavation, for example on soft clay, alluvial deposits, compressible fill, and so on.
• Settlement, or differential settlement is likely.
• Where it may be impractical to create separate strip or pad foundations for a large number of individual loads. In very general terms, if strip or pad foundations would cover 50% or more of the floor area, then a raft may be more appropriate.

Raft foundations can be fast and inexpensive to construct, as they tend not to require deep excavations compared to strip or pad foundations and they may use less material as they combine the foundation with the ground slab. However, they tend to be less effective where structural loads are focussed on a few concentrated areas, and they can be prone to erosion at their edges.

The design of raft foundations involves a number of disciplines, as consideration must be given not only to the structure itself, but also to; integration of other constructions (such as external walls), insulation, damp proofing and complex ground conditions such as the presence of groundwater, trees or contamination.

Raft foundations are generally constructed on a compacted hardcore base (perhaps 100 mm thick). A layer of blinding concrete (typically 50 mm) may then be laid with a waterproof membrane above to create an even, dry surface to allow formation of the raft .

The concrete raft tends to include steel reinforcement to prevent cracking, and may incorporate stiffening beams or thickened areas to provide additional support for specific loads, for example, below internal walls or columns (which may require punching shear reinforcement). Beams may stand proud of the raft, either above or below it, or may be 'hidden' beams, formed by reinforced areas within the depth of the raft itself. These thickened areas are particularly useful where there are poor ground conditions, as the required thickness of the raft itself might otherwise be uneconomic.

Typically, a thickened reinforced area is created at the perimeter of the raft to form an edge beam supporting the external walls of the building. A concrete toe often supports the external leaf of the wall.

Insulation will generally be laid on top of the raft, with a concrete floor, or raised floor above.

Drainage may be required under raft foundations in some circ*mstances, and geotextile barriers may be required to prevent free-draining materials from becoming clogged up by the surrounding soil.

Types of raft foundation include:

• Solid slab raft, sometimes referred to as a plain raft, and including; flat rafts, mats, wide toe rafts, slip plane rafts, blanket rafts, and so on.
• Slab beam raft.
• Cellular raft.
• Piled raft.

For more information, see Types of raft foundation.

Where soil is compressible, a raft foundation may be formed as a compensated foundation. In this case, the raft slab is provided to a depth that the weight of the excavated soil is equal to the raft slab weight plus that of the structure to be supported. This can be appropriate when constructing buildings on soft clay or loose sand, as settlement can be significantly reduced.

For more information see: Compensated foundation.

• Blinding.
• Building foundations.
• Cast-in-place concrete.
• Cellular raft foundation.
• Compensated foundation.
• Footings in foundations
• Pad foundation.
• Pile foundations.
• Piled raft foundation.
• Raft system.
• Strip foundation.
• Trench fill foundation.
• Types of pad foundation.
• Types of raft foundation.