Two questions I see often and seem to cause dramaare What knit stitch doI use if the pattern doesn’t specify?andWhat is the difference between the different knit stitches? But my favorite is Why are there so many knit stitches in loom knitting? While it does seem like there are a lot of knit stitches, there arestillonly two. Knit and e-wrap knit. The confusion occurs because there are 3 ways to make a knit stitch. And all 3 have different tensions. So let’s discuss each one and then compare all 4 so we can put that drama to rest.
E-wrap Knit Stitch
I will start with the e-wrap knit since it is usually the first stitch a person learns when he or she picks up a loom for the first time. E-wrap knit is the loosest knit stitch. It is taller and uses more yarn than a true knit or purl stitch. It is a twisted stitch so the stitch looks like a y instead of the classic v of the knit stitch. When worked in a flat panel, the e-wrap knit gives a great texture to the project since the stitches slant in the opposite way on each row.
When worked in the round, the stitches will slant in the direction that you work.
You make an e-wrap knit by bringing the working yarn behind the peg, around to the front of the peg,
andthen on around to the backthe peg like a cursive e.
After the peg is wrapped, the working yarn is behind the peg again.
Then you knit over by bringing the bottom loop up and over the new loop you just made.
Knit Stitch
The knit stitch can be produced 3 different ways, and the size of the stitch varies with one.
- True Knit Stitch
Let’s look at the true knit stitch first. It is also called the traditional knit stitch. Some people call it a reverse purl even though it’s actually more accurate to call a purl a reverse knit. It is the same height and width of a purl stitch and is best to use when working alongside purls in the rib, garter, seed, and moss stitches.
You make a true knit stitch by bringing the working yarn above the existing loop.
You bring your pick up through the existing loop andcatch the working yarn.
Thenpull it down through the loop to create a new loop.
You then take the old loop off the peg.
Thenplace the new loop back on the peg.
Snug up the yarn by gently tugging the working yarn.
Why does this look just like a purl stitch? This stitch is not to be confused with the purl. While the motions appear to be the same, the purl is worked in reverse. The working yarn is at the bottom of the existing loop, and the new loop is pulled up from the bottom before taking the old loop off the peg and replacing the new loop on.
- U-wrap Knit Stitch
Next is the u-wrap knit. It is shorter and tighter than the true knit stitch.
You make a u-wrap knit by bringing the working yarn above the existing loop in front of the peg and pulling it straight back behind the peg without completely wrapping it.
Then pull the bottom loop up
and over.
- Flat Knit Stitch
The last way to create a knit stitch is the tightest and smallest of the knit stitches. It is the flat knit. It can get very tight after just a couple of rows. Flat knit stitch works best withfibers that stretch like wool. It is extremely hard to use the flat knit on yarn that have no stretch like cotton.
You work the flat knit by bringing the working yarn across the front of the peg above the existing loop without any wrap of the peg.
Then bring the existing loop up
and over.
Comparison
I worked 4 swatches using each of the techniques mentioned. I made all 4 with 16 pegs on the Sock Loom 2 and worked 25 rows using KnitPicks Wool of the Andes worsted weight yarn. I worked all 4 with the chain cast on and used the basic bind off. I also slipped the first stitch on each row.
From left to right: e-wrap knit, true knit, u-wrap knit, and flat knit.
You can see the difference in size with the e-wrap being the largest and loosest and the flat knit being the smallest and tightest. You can also see how the chain cast on (at the top) was not tight enough as the stitches got tighter and smaller. You will need to take your cast on into consideration with whichever knit stitch technique you use. I controlled my tension on all the swatches by not pulling on the yarn as I worked the stitches. Each of them could have been made tighter by simply pulling and stretching the yarn.
Here is the gauge I achieved with each swatch. What is gauge? Gauge is simply the number of stitches in an inch by the number of rows in an inch. The more stitches or rowsin aninch means the gauge issmaller. Thefewer stitches or rows in an inch means the gauge is larger. Some patterns will list gauge in a 2” or 4” square. I will discuss gauge more innext month’s article.Forthis demonstration,I will listgauge per inch.
- E-wrap knit stitch: 3.5 stitches by 5 rows per inch
- True knit stitch: 3.75 stitches by 5.5 rows per inch
- U-wrap knit stitch: 4 stitches by 6 rows per inch
- Flat knit stitch: 5.5 stitches by 7.5 rows per inch
So as you can see, it makes a big difference in size depending on how the knit stitch is made. Why can I not use e-wrap on every pattern? Everyone’s tension is different. If you were to make the same exactswatch I have, youmost likely will have a different gauge.Designerswrite their pattern for a certainlook or size. While you can interchangethe knit stitch and the e-wrap knit insome patterns, most times it will change the pattern too much in size. If using the knit stitch, you can adjust your tension by using a differentknit stitch technique. You can also adjust your tension on the flat and u-wrap knit stitches by loosening them as you work the stitches. I loosen my u-wrap knit by simply pushing the stitch back with my pick afterpulling the loop over. But these swatches were made without loosening the stitches. They were made as described above.
I hope this helpsclarify the knit stitch dilemma andputs the drama to rest.
