How to install an SSD in a PC (2024)

How-To

We show you how to do it with an M.2 or SATA SSD.

By Adam Patrick Murray

Feb 25, 2021 3:01 am PST

Image: Adam Patrick Murray/IDG

Installing an M.2 or SATA SSD in your desktop is an essential part of every PC build, or an easy upgrade to make your PC feel faster. Luckily, installing an SSD is easier than finding the best one (we have a roundup for that!) or even understanding how they work. I’m not going to cover any of that here, but I’ll walk through installing both kinds.

The steps below should apply to almost any model. I’ll start with the M.2 SSD because it’s a bit more tricky to install, and there are some things to research before you do it. Click this link to jump to the section on SATA SSDs.

How to install an M.2 SSD in a desktop PC

An M.2 SSD looks like a stick of chewing gum with chips on one side, a label on the other, and gold contacts at one end. Some will install just like that. Some will come with their own heat sinks and look more like a pack of gum than a stick of gum. Some motherboards will have a shield for the M.2 slot, and you’ll have to shimmy the drive underneath it. We’ll cover all the forms below.

Step 1: Find the M.2 slot

The first thing you want to do is find where the M.2 slot is on your motherboard. Look for a slot about one inch wide that protrudes from the motherboard about a quarter of an inch. Every motherboard is different, but the most common locations are below the CPU and around the PCIe slots in the lower half of the board. Check the manual if you have trouble finding it.

Some motherboards have a pre-installed shield in place that serves as a heat spreader but also can provide a nice piece of visual flair. This will obviously have to be removed before you access the M.2 slot.

If your motherboard supports two M.2 SSDs you’ll need to consult your manual to see which slot is the recommended one for installing your boot drive. Each slot might offer different performance levels, while others might turn off a PCIe slot if used. In short, read the manual first!

Step 2: Find the M.2 Mounting System

Once you’ve found the right slot, find the screw about three inches to the left that is inserted into a standoff. The standoff is there because when the drive is inserted, there will be a gap between the SSD and the motherboard. The standoff plays the crucial role of keeping the drive flat.

If your motherboard doesn’t have the screw or standoff, look in the box—it might be in a small plastic bag. If your motherboard features an M.2 shield, you’ll need to find two screws that mount it to the motherboard.

Step 3: Prep for M.2 SSD installation

Now it’s time to touch something metal, like a metal furniture leg, in order to ground yourself, then grab a screwdriver. Unscrew the screw from the standoff and place it somewhere safe—you do not want to lose a screw, or have it roll around on your motherboard.

For those of you with a shield, unscrew it from the motherboard but take note of the underside, where there should be a thermal pad with a piece of plastic over it. Do not remove the plastic yet—just place the shield somewhere safe.

The most common M.2 size is 80 millimeters, but in any case you need to make sure the standoff is positioned correctly for your size of drive. Hover the drive over the slot and take note of the length. If necessary, use pliers to loosen the standoff and move it to the appropriate length position. Make sure the standoff is screwed in fully–not too tight, just snug. You don’t want it spinning while we are trying to install the screw.

For those of you with shields, you most likely don’t have a standoff. Instead there should be a squarish brace of some sort for the drive to rest on while the shield holds it in place.

Step 4: M.2 SSD installation

The next step is to insert the drive. Consider the “top” of the drive to be the side with the brand’s label or sticker. The edge with the semi-circle notch is what’s going to be held in place by the screw. The edge with gold contact points is what we insert into the M.2 slot.

There’s a tiny notch dividing the contact points into two sections. You’ll want to line up that notch with a notch inside the M.2 slot, with the top of the drive facing up. Insert the drive firmly at about a 15-degree angle until there’s no more give, and let go.

If you have a screw and standoff-based system you’ll want to press down on the drive so that it lies flat, and the semi-circlular notch lines up with the standoff. While holding the drive flat, insert the screw and tighten to a comfortable point. Take care notto overtighten, or you risk damage to the drive, the screw, or the motherboard. If you’ve installed it correctly, the drive should not shift in place at all.

M.2 SSD Install: Final Notes

The last thing to note here is that some M.2 SSDs feature their own built-in heat sink. An Adata XPG Gammix S70 drive we reviewed had a heat sink so big, it made the drive a challenge to install. Most of the ones we’ve tested are less obtrusive.

If your motherboard has a shield you don’t want to place that over the included heat sink. Just store the shield somewhere safe in case you need to use it in the future.

Next, we dive into installing a 2.5-inch SATA SSD.

How to install a 2.5-inch SATA SSD in a desktop PC

Now let’s move on to installing a 2.5-inch SATA SSD. This installation is much more dependent on the PC case you are using and where you want to place it, so there’s an endless variety of possibilities.

Instead of an exact step-by-step guide, we’ll cover the basics that will always apply to every installation. Once again I’m assuming you already have a drive in hand, if not check out our roundup of the best SSDs.

The two most common options for installing the drive in a PC is either to put it in a drive cage or to secure it to the case itself. Drive cages usually have some sort of method to attach the drive to the tray, and the tray slides into a cage.

Mounting it to the case can involve either screwing the drive to the metal, or putting the drive into a tray first and then attaching it. Either way take care to make sure you have enough cable length to safely route the cables inside the case.

Installing a 2.5-inch SATA SSD: Required cables

When installing a 2.5-inch SATA SSD you will always need two things: a SATA data cable and access to a SATA power cable. Most motherboards include a SATA data cable, which is used for data transmission from the drive to the motherboard. Look for a long, thin, and flat cable—sometimes with an L-shaped connector at the end.

The SATA power cable, which provides power to the drive, will be included with the power supply. It usually has multiple connectors.

Installing a 2.5-inch SATA SSD: Attaching the cables

In order to use the SSD you will need to have both cables attached and secured to the drive at all times. Depending on where you install the drive in the case it might be easier to plug the cables in before you mount the drive.

Plugging in both cables is simple: Look for the end of the drive that has the connections, and note there are two. The shorter port is for the interface cable, and the longer port is for the power cable. If you look closely, each port is keyed with a tiny notch that indicates the correct orientation for the cable to plug into.

Because of this there is only one way to install the cable, so line them up and insert firmly. The interface cable includes a primitive locking mechanism that gives a subtle click when inserted. The power cable does not lock in, so be sure to press it in all the way for a secure connection.

Installing a 2.5-inch SATA SSD: Connection to Motherboard

The interface cable will then need to be plugged into the motherboard. There will most likely be multiple ports to choose from, so now is another time you should consult your manual.

You’ll need to find where the manual refers to the SATA ports on your motherboard. To get the maximum bandwidth out of your SSD you’ll want to connect to the SATA 6Gbps ports, but the slower 3Gbps ports will work fine as well.

In this example you can see that this motherboard features six SATA 6G ports, and they are stacked into three columns of two ports. Typically you’ll want to use the ports in order, so if the numbering starts at one, choose that and identify which port it is on the motherboard itself.

On any remotely modern PC, the performance should be the same, but on an older PC the first port is usually the highest-performing. When the ports are stacked like this sometimes it can be a bit confusing knowing which number is which, so just take your time and look closely. This cable will lock into place, so after you insert it in enough you will hear a subtle click to know you are secure.

Installing a 2.5-inch SATA SSD: Final notes

As we close out SATA SSD installation, a few useful notes.

Some of the SATA data connectors feature an L-shaped plug, shown below.

The L-shaped plug is useful for situations where you need to keep a low profile so the cable doesn’t get pinned somewhere. Both the L-shaped and the straight cables offer the same performance.

The SATA power cable will most likely have multiple ports on it. This is to allow you to attach multiple drives or peripherals onto the same cable.

Which plug you use will depend on the length you need to reach to plug in the drive and whether that cable also needs to reach other ports. All the plugs will work just the same.

Finally, a Windows 10 tip! If you are installing both an M.2 and SATA SSD you might be confused as to which drive is which when it comes time to install Windows.

One way to get around that is to keep the SATA SSD unplugged while you’re going through the installation process, so there’s no option for installing Windows other than the higher-performance NVMe SSD. After you’re up and running, plug the SATA drive back in, format it, and you’re ready to roll.