Cisco Router basic commands (2024)

Cisco routers are a popular choice for network administrators due to their robustness and reliability. They are used in a wide range of environments, from small home networks to large enterprise networks. To effectively manage a Cisco router, it is essential to have a good understanding of the basic commands that are used to configure and troubleshoot the device. In this article, we will take a look at some of the most commonly used Cisco router basic commands, with examples and explanations to help you understand how they work.

Accessing the Cisco Router

The first step in configuring a Cisco router is to access the device. This can be done using a variety of methods, including Telnet, SSH, and the Cisco Configuration Professional (CCP) tool. The most common method is to use Telnet or SSH to access the router's command-line interface (CLI). To do this, you will need to know the IP address of the router and have a Telnet or SSH client installed on your computer.

To access a Cisco router using Telnet, open a command prompt and enter the following command −

telnet IP_ADDRESS

For example, to access a router with the IP address of 192.168.1.1, you would enter the following command −

telnet 192.168.1.1

To access a Cisco router using SSH, open a command prompt and enter the following command −

ssh USERNAME@IP_ADDRESS

For example, to access a router with the IP address of 192.168.1.1 using the username "admin", you would enter the following command −

ssh [email protected]

Once you have accessed the router, you will be prompted to enter a username and password. If you are using Telnet, the default username is "admin" and the default password is "password". If you are using SSH, the default username and password are both "admin".

Basic Router Configuration Commands

Once you have accessed the router, you can start configuring the device. The following are some of the most commonly used Cisco router basic commands for configuring the device −

• enable − This command is used to enter enable mode, which gives you access to all of the router's configuration commands.

• configure terminal−This command is used to enter global configuration mode, which allows you to make changes to the router's global configuration.

• interface interface_name − This command is used to enter interface configuration mode, which allows you to make changes to a specific interface on the router.

  See Also

  Login and Account HelpCCNA Training » Configure SSH for Remote Access on Cisco RouterWhat is Cisco Default Password and How to Protect Sensitive DataHow to Log into the Graphical User Interface (GUI) of a Cisco Business Router

• hostname hostname − This command is used to set the hostname of the router.

• ip address IP_ADDRESS SUBNET_MASK − This command is used to configure the IP address and subnet mask of an interface.

• no shutdown − This command is used to enable an interface that has been previously shut down.

• exit − This command is used to exit the current configuration mode and return to the previous mode.

• end − This command is used to exit configuration mode and return to privileged mode.

For example, to set the hostname of a router to "Router1", you would enter the following commands −

enableconfigure terminalhostname Router1end

To configure the IP address and subnet mask of an interface named "FastEthernet0/0", you would enter the following commands −

enableconfigure terminalinterface FastEthernet0/0ip address 192.168.1.1 255.255.255.0no shutdown

Basic Router Troubleshooting Commands

In addition to configuring a Cisco router, it is also important to know how to troubleshoot the device. The following are some of the most commonly used Cisco router basic commands for troubleshooting −

• show running-config − This command is used to display the current configuration of the router.

• show interfaces − This command is used to display information about all of the interfaces on the router, including their status, IP address, and bandwidth usage.

• show ip route − This command is used to display the routing table of the router, which shows the paths that packets take to reach their destination.

• ping IP_ADDRESS − This command is used to test the connectivity between the router and a specific IP address.

• traceroute IP_ADDRESS − This command is used to trace the path that packets take to reach a specific IP address, and to identify any issues along the way.

• debug command − This command is used to enable debugging for a specific function, such as routing or authentication.

  See Also

  SSH to the Router - GL.iNet Router Docs 3

For example, to display the current configuration of a router, you would enter the following command −

show running-config

To display information about all of the interfaces on a router, you would enter the following command −

show interfaces

To test the connectivity between a router and an IP address of 192.168.1.100, you would enter the following command −

ping 192.168.1.100

To trace the path that packets take to reach an IP address of 8.8.8.8, you would enter the following command −

traceroute 8.8.8.8

To enable debugging for routing on a router, you would enter the following command −

debug ip routing

Conclusion

Cisco routers are a powerful and versatile tool for managing networks. To effectively manage a Cisco router, it is essential to have a good understanding of the basic commands that are used to configure and troubleshoot the device. This article has provided a comprehensive guide to some of the most commonly used Cisco router basic commands, with examples and explanations to help you understand how they work. By mastering these commands, you will be able to effectively manage and troubleshoot your Cisco router, and keep your network running smoothly.