Change IP address of a network adapter - Windows Server (2024)

This article provides some information about how to change the IP address of a network adapter.

Original KB number: 323444

Summary

This article describes how to change the Internet Protocol (IP) address that is assigned to a network adapter. An IP address may be assigned automatically if your network has a Dynamic Host Configuration Protocol (DHCP) server, or you can specify an IP address.

How to change the IP address assigned to a Network Adapter

1. Log on to the computer by using the Administrator account.
2. Click Start, point to Control Panel, and click Network Connections.
3. Right-click the local area connection that you want to modify and then click Properties.
4. In the This connection uses the following items box, click Internet Protocol (TCP/IP), and then click Properties. The Internet Protocol (TCP/IP) Properties dialog box appears.
5. Continue with the steps in one of the following two sections, depending on your circ*mstances.

How to automatically obtain an IP Address

Follow these steps to configure the computer to obtain an IP address from a DHCP server. You must have a DHCP server.

1. Click Obtain an IP address automatically.

2. Click Obtain DNS server address automatically if you do not want to specify the IP address of the Domain Name System (DNS) server.

3. Click OK. In the Local Area Connection Properties dialog box, click Close.

4. In the Local Area Connection Status dialog box, click Close.

5. Click Start, and then click Run.

6. In the Open box, type cmd, and then click OK.

   See Also

   Configuring IP Network Interfaces

7. At the command prompt, type ipconfig /release, and then press ENTER.

8. Type ipconfig /renew, and then press ENTER.

   The network adapter is assigned an IP address by the DHCP server, and a message similar to the following appears:

   Windows Server IP Configuration Ethernet adapter Local Area Connection: Connection-specific DNS Suffix. :dns.microsoft.com IP Address. . . . . . . . . . . . :192.168.0.201 Subnet Mask . . . . . . . . . . . :255.255.255.0 Default Gateway . . . . . . . . . :192.168.0.1

9. Type exit, and then press ENTER to quit the command prompt.

How to Specify an IP Address

To assign an IP address to the network adapter, follow these steps:

1. Click Use the following IP address if you want to specify the IP address for the network adapter.
2. In the IP address box, type the IP address that you want to assign to this network adapter. This IP address must be a unique address in the range of addresses that are available for your network. Contact the network administrator to obtain a list of valid IP addresses for your network.
3. In the Subnet mask box, type the subnet mask for your network.
4. In the Default gateway box, type the IP address of the computer or device on your network that connects your network to another network or to the Internet.
5. In the Preferred DNS server box, type the IP address of the computer that resolves host names to IP addresses.
6. In the Alternate DNS server box, type the IP address of the DNS computer that you want to use if the preferred DNS server becomes unavailable.
7. Click OK. In the Local Area Connection Properties dialog box, click Close.
8. In the Local Area Connection Status dialog box, click Close.

Troubleshooting

• There is an IP address conflict: If you try to assign an IP address that is already in use, you receive the following error message:

  The static IP address that was just configured is already in use on the network. Please reconfigure a different IP address.

  In this case, assign an unused IP address to the network adapter.

• Your computer cannot connect to other computers on the network: If you assign an incorrect subnet mask address to the network adapter, the computer is effectively located on a different network. You cannot connect to other computers on the network.

• Your computer cannot connect to other computers by using host names: If you assign an incorrect DNS server IP address, or if you do not use a DNS server, you cannot connect to computers by using their host names. It prevents you from browsing the Internet. You can connect to other computers by using their IP addresses.

  To work around this issue in a local network, add host-name-to-IP-address mappings in a Hosts file.